1900 watts PV, (1000 watts PV feeding MX60; 900 watts PV + 160 watts micro hydro both feeding into a single shared Morningstar TS-MPPT-60) ; 2 SureSine 300; Xantrex Pure Sine 1800/12; six Rolls Surrette 2 volt L16 @ 12 volts.
Domestic hot water totally provided by the sun 8 months out of every year via thermal panel.
I just noticed something after deciding to go with 20W panels instead of 30W panels due to the overall size of the panels.
The 24v 20W panel produces 0.61 Amps as can be seen here.
Hooking two of those 24v 20W panels in parallel is going to double the Amps to give us: 1.22A total.
The 12v 20W panel produces 1.17 Amps as can be seen here.
Hooking two of those 12v 20W panels in series is going to keep our Amps the same and still give us 1.17A total.
So in this case, it's better to go with the 24v setup above correct? Again, I had to change from 30W to 20W panels because again I'm limited on space I found after measuring, the 30W panels would be a little too long.
Me loves some solar
Vmp on the "24 Volt" panel: 33
Vmp on two "12 Volt" panels in series: 34.4
What this means in terms of charging a 24 Volt battery with a PWM controller: not much difference.
The current the panel produces at its Imp is not necessarily the same as the current the battery charges at once the controller and all the wire is in place.
Typically a "24 Volt" panel will have a Vmp of 35. The two "12 Volt" units in series come closer to this by 1.4 Volts. But that could make up for the Voltage drop through the wires.
Four 175 Watt panels, OB MX60, 232 Amp hrs, OB 3524, Honda eu2000.
Ohm's Law: Amps = Volts / Ohms
Power Formula: Watts = Volts * Amps
i don't recall the question in the other thread going into the number of 12v pvs it would take to charge a 36v battery bank specifically and i believe if i'm remembering correctly that you wanted to split the batteries into differing voltage loads which you should not do on a battery bank. simply, if a pv can properly charge 1 12v battery then suffice it to say that 2 of the same pvs will charge 2 of the same 12v batteries. do realize too that when we refer to a pv as being a 12v pv that the output vmp of that pv is far above 12v and that 12v rating is for the typical charge requirements presented at that nominal 12v rating that is used by batteries.
somehow, i feel you are leaving pertinent questions out of this like is a 20w pv enough to charge your particular battery and what these batteries are to power.
Me loves some solar
I've got a system similar to the original poster's that I am trying to set up. I've got two 30W 12v panels wired in series that I'd like to charge two 12v 55Ah gel acid batteries, so it's really a 24v system on both ends.
The problem I'm having is finding a solar charge controller that could handle this set up, does anyone have any recommendations? I have a cheap instapark 24v 10A one in place, and while it passes the battery voltage to my load, it doesn't seem to charge the batteries at all. The solar array is sending out ~38v.
Thanks for any help you can give me.
without more specs for the panels, one cannot give a definitive answer.... but... you are shy by at least 2 more panels probably as much as 4 short or more... that is why they are not charging, not enough amps total
100% Off Grid @ 51* 46' N lat 124* 44' W long
New House system: coming - 2 arrays @ 2240W
CL150&Epanel 2 @140 W 12v PVs , 24V C&D AT-15P AGM @ 950Ah
+ CL150 2@120W 12 V panels, 24V C&D AT-15P AGM @ 950Ah
Cotek ST1500W inverter, TBS 30a-24v Omni-charger, Honda Eu3000is,
Guest cabin system: 3 - 70W panels to SB 2000e CC, with 2 - 100 ah 12v SAFT wet NiCd's , 600W TSW Inverter